Get Your Free Guide to Changing Can Lights

Understanding Can Lights and Why They Need Replacing

Can lights, also called recessed lights or downlights, are lighting fixtures that sit inside your ceiling, creating a clean, flush appearance. The housing of a can light sits above the ceiling line, while the trim ring and bulb are visible below. These fixtures are popular in kitchens, bathrooms, living rooms, and basements because they provide focused light without taking up space on walls or hanging from the ceiling.

Free Guide to Delta Platinum Medallion Benefits →

Can lights need replacing for several reasons. The most common reason is that the bulb has burned out. In older homes, these fixtures often use incandescent or halogen bulbs that typically last 1,000 to 2,000 hours. That means a bulb used for four hours per day might last about one to two years. Newer LED can lights last much longer—often 25,000 to 50,000 hours or more—which can mean 15 to 25 years of use depending on daily usage patterns.

Sometimes the entire fixture needs replacing, not just the bulb. This happens when the housing has become damaged, when the electrical components have failed, or when you want to upgrade to newer technology. A fixture might also need replacing if it's outdated, inefficient, or if you're updating your home's lighting design for aesthetic reasons.

Understanding whether you need to replace just the bulb or the entire fixture is your first step. This guide provides information about both situations so you can understand what's involved in the process.

Practical Takeaway: Before you begin, identify whether your can lights are functioning but need new bulbs, or if the entire fixture requires replacement. This determines which steps you'll follow and what materials you'll need to gather.

Safety Considerations Before You Start

Working with electrical fixtures requires serious attention to safety. The most critical step is turning off power to the lights you're working on. Locate the circuit breaker panel in your home—usually found in a basement, garage, or utility closet. Open the panel and look for the breaker that controls the lights you want to work on. Switch that breaker to the "off" position. If you're unsure which breaker controls your can lights, you can have someone flip switches while you watch the lights, or you can test the breaker by attempting to turn on the lights after switching it off.

Your Free Guide to Davenport Driver's License and Registration →

After switching off the breaker, wait a few minutes before touching any fixture parts. This allows any residual electrical charge to dissipate. Test the light switch to confirm the power is truly off—try flipping it several times to be sure no light comes on.

Before working inside the ceiling cavity, wear safety glasses to protect your eyes from dust and insulation particles. If your home was built before the 1980s, the insulation in your ceiling may contain asbestos. Do not disturb this insulation. If you suspect asbestos is present, consult a professional asbestos abatement company rather than attempting the work yourself.

Use a sturdy ladder or step stool—not a chair—to reach your ceiling fixtures safely. Make sure the ladder is on level ground and fully stable before climbing. Keep both hands free for working, so ask someone to hold the ladder if possible.

If you're replacing the entire fixture, you may encounter old wiring that's cracked or brittle. If this occurs, stop work and contact a licensed electrician. Damaged wiring creates a fire hazard and should not be handled by untrained individuals.

Practical Takeaway: Always turn off power at the breaker, confirm the power is off by testing the light switch, wear protective eyewear, use a proper ladder, and stop immediately if you encounter damaged wiring or suspect asbestos insulation.

Steps for Replacing Just the Bulb

If your can light fixture is working but the bulb has burned out, replacement is straightforward and takes only minutes. First, turn off the power at the breaker and confirm it's off. Use your ladder to reach the fixture safely and position yourself directly below the light.

Change Your Pointer Size Across All Operating Systems →

Most can light bulbs are held in place by a simple twist-and-turn mechanism, similar to a standard household light bulb. Grasp the bulb gently and turn it counterclockwise—the direction of left-handed threads. The bulb will release from the socket. Some bulbs, particularly certain LED models, may be held in place with a different mechanism like a pin base or bayonet fitting. Check your fixture documentation if you're unsure of your bulb type.

Before installing a new bulb, check the wattage and type required by your fixture. This information is usually printed on the inside of the housing or trim ring. Never exceed the recommended wattage, as this can overheat the fixture and create a fire risk. If your fixture says "100W maximum," do not install a bulb rated for 100W if you're uncertain—aim for 75W or less to be safe, or install an LED bulb which uses far less wattage while producing similar brightness.

LED bulbs offer significant advantages over incandescent or halogen bulbs. They produce the same amount of light while using about 75% less energy. They generate less heat, which reduces fire risk and is safer for recessed fixtures. They last 20 to 50 times longer than traditional bulbs. LED bulbs do cost more upfront—typically $8 to $20 per bulb compared to $1 to $3 for incandescent—but the longer lifespan and lower energy costs mean you'll save money over time.

When choosing an LED bulb, look for the color temperature measured in Kelvin (K). A 2700K bulb produces warm white light similar to traditional incandescent bulbs. A 4000K bulb produces neutral white light good for kitchens and work areas. A 5000K or higher produces cool white light often preferred in modern spaces. Check whether your fixture is dimmable and choose a bulb that matches.

Insert the new bulb into the socket and turn it clockwise until it's snug. Do not force it excessively. Turn the power back on and test the light. If it doesn't come on, turn the power off again and check that the bulb is fully seated.

Practical Takeaway: Bulb replacement requires turning off power, knowing your fixture's wattage limits, choosing the correct bulb type and color temperature, and installing securely. LED bulbs cost more initially but provide long-term savings through reduced energy use and longer lifespan.

Steps for Replacing the Entire Fixture

If your can light housing is damaged, the fixture won't turn on even with a new bulb, or you want to upgrade the entire unit, you'll need to replace the whole fixture. This is more complex than bulb replacement but is manageable for someone with basic DIY skills.

Free Guide to Dental Implant Programs in Oakland →

Start by turning off power at the breaker and confirming it's off. Use your ladder to reach the fixture. From above the ceiling, if you have attic access, you'll see the fixture housing with wiring connected to it. From below, you'll need to work from inside the ceiling cavity after removing the trim ring and old housing.

To remove the trim ring, look for small clips or screws holding it to the housing. These are usually located on the sides or bottom of the ring. Gently pull down or unscrew as needed. The trim ring should release, and you may need to wiggle it slightly to free it completely.

Next, locate the housing itself inside the ceiling cavity. It will be attached to the ceiling framing with brackets, clips, or screws. Loosen these fasteners to free the housing from the ceiling structure. You may also encounter insulation around the housing—carefully move it aside, but do not remove it from the rest of your ceiling.

Once the housing is loose, you'll see the electrical wiring connected to it. There will be two main wires—typically black (hot) and white (neutral)—and a bare copper or green wire (ground). These wires may be connected with wire nuts (small plastic connectors twisted onto the wire ends) or with a terminal block (a small plastic device with screw terminals). If they use wire nuts, twist them counterclockwise to disconnect. If they use a terminal block, loosen the small screws holding each wire and pull the wires free.

Remove the old housing completely. Before installing the new one, check the type of fixture you're